Single branch specified, using that and the previous one:
   remotes/brancher/net-next-hw-2025-11-05--16-00 (v6.18-rc3-741-g116f9cae4b08)
   remotes/brancher/net-next-hw-2025-11-06--00-00 (v6.18-rc3-798-g89387a4289ea)

==== BASE IDENTICAL ====
==== COMMIT DIFF ====
diff --git a/tmp/tmp.xE1kcctlEi b/tmp/tmp.tCM2RKTNAA
index d61997f26fa2..d998e380cb50 100644
--- a/tmp/tmp.xE1kcctlEi
+++ b/tmp/tmp.tCM2RKTNAA
@@ -13,6 +13,63 @@ nipa: config: x86: use periodic HZ tick
 nipa: disable 6.17's merge window kunit tests
 nipa: disable random kunit tests
 nipa: fbnic: link up on QEMU
+net: bonding: use atomic instead of rtnl_mutex, to make sure peer notify updated
+net: phy: qt2025: Wait until PHY becomes ready
+selftests/bpf: Add mptcp test with sockmap
+net,mptcp: fix proto fallback detection with BPF
+mptcp: disallow MPTCP subflows from sockmap
+net: ethernet: broadcom: bgmac: add SPDX license identifier
+net: bridge: fix MST static key usage
+net: bridge: fix use-after-free due to MST port state bypass
+net: ethernet: fix uninitialized pointers with free attr
+tcp: add net.ipv4.tcp_comp_sack_rtt_percent
+lan966x: Fix sleeping in atomic context
+bonding: fix NULL pointer dereference in actor_port_prio setting
+net: phy: microchip_t1s:: add cable diagnostic support for LAN867x Rev.D0
+net: phy: phy-c45: add OATC14 10BASE-T1S PHY cable diagnostic support
+net: enetc: add port MDIO support for ENETC v4
+net: enetc: set external MDIO PHY address for i.MX94 ENETC
+net: enetc: set external MDIO PHY address for i.MX95 ENETC
+net: wan: framer: pef2256: Switch to devm_mfd_add_devices()
+net: dsa: microchip: Fix reserved multicast address table programming
+net: txgbe: remove wx_ptp_init() in device reset flow
+net/sched: Fix possible infinite loop in qdisc_tree_reduce_backlog()
+eea: introduce ethtool support
+eea: create/destroy rx,tx queues for netdevice open and stop
+eea: probe the netdevice and create adminq
+eea: introduce ring and descriptor structures
+eea: introduce PCI framework
+tools: ynltool: add traffic distribution balance
+tools: ynltool: add qstats support
+tools: ynltool: add page-pool stats
+tools: ynltool: create skeleton for the C command
+netlink: specs: netdev add missing stats to qstat-get
+ptp: Return -EINVAL on ptp_clock_register if required ops are NULL
+net: ravb: Use common defines for time stamping control
+net: ravb: Break out Rx hardware timestamping
+net: rcar_gen4_ptp: Remove unused defines
+net: rtsn: Use common defines for time stamping control
+net: rswitch: Use common defines for time stamping control
+net: rcar_gen4_ptp: Move control fields to users
+net: rswitch: Move definition of S4 gPTP offset
+selftest: netcons: add test for netconsole over bonded interfaces
+selftest: netcons: create a torture test
+selftest: netcons: refactor target creation
+net: netpoll: fix incorrect refcount handling causing incorrect cleanup
+net: gro_cells: Reduce lock scope in gro_cell_poll
+iavf: clarify VLAN add/delete log messages and lower log level
+net/ipv6: drop ip6_route_get_saddr
+net/ipv6: use ipv6_fl_get_saddr in output
+net/ipv6: create ipv6_fl_get_saddr
+net/ipv6: flatten ip6_route_get_saddr
+net/mlx5e: Fix return value in case of module EEPROM read error
+net: ti: icssg-prueth: Fix fdb hash size configuration
+dt-bindings: ethernet: eswin: fix yaml schema issues
+selftests: net: local_termination: Wait for interfaces to come up
+net/mlx5e: SHAMPO, Fix header formulas for higher MTUs and 64K pages
+net/mlx5e: SHAMPO, Fix skb size check for 64K pages
+net/mlx5e: SHAMPO, Fix header mapping for 64K pages
+net: libwx: fix device bus LAN ID
 idpf: add support for IDPF PCI programming interface
 net: dsa: add driver for MaxLinear GSW1xx switch family
 net: dsa: add tagging driver for MaxLinear GSW1xx switch family